DisplayPort Audio/Video with RS-232 Serial and IR Control over IP Extender Kit, 1920 x 1080 (1080p) @ 60 Hz, 200 m

The B160-101-DPSI DisplayPort Audio/Video with RS-232 Serial and IR Control over IP Extender Kit extends and distributes DisplayPort audio/video, RS-232 serial and IR (infrared) remote signals through a dedicated Ethernet network switch* located up to 100 m (328 feet) from the transmitter. With an additional 100 m (328 feet) between the switch and the receiver, the maximum distance from source to display is 200 m (656 feet). You can also directly connect the transmitter and receiver up to 328 feet apart with Cat5/Cat6 cabling. The B160-101-DPSI is designed for managed network switches with IGMP, which allow login and remote management via switch interface. You can connect up to 64 transmitters and 255 receivers in a single managed switch installation.** The B160-101-DPSI supports video resolutions up to 1920 x 1080 (1080p) at 60 Hz. In a point-to-multipoint switch installation, you can send the DisplayPort video source to any analog or digital display, including VGA and HDMI. It extends IR control signals that control a source, such as a Blu-ray™ player, from a remote display, as well as RS-232 signals at serial baud rates up to 57600 Bps. *B160-Series designed for use with dedicated network switch. Connecting to a switch used with other networking equipment will result in degraded or non-functional performance. **Unmanaged switch installations are limited to two transmitter units. Number of receivers is limited to number of ports remaining on unmanaged switch.

Extends and Distributes DisplayPort A/V, Serial and IR Control Signals over Cat5/6 Cabling
● Converts source video to IP-based signal transmitted to and distributed through network switch
● Transmitter and receiver each extend signal up to 100 m (328 ft.) from switch for maximum distance of 200 m (656 ft.)
● Transmitter and receiver can also connect directly without switch up to 100 m (328 ft.) apart

Designed for Managed Network Switches with IGMP
● Allows login and remote management via switch interface
● Connect up to 64 transmitters and 255 receivers in single managed switch installation
● HDMI output on transmitter for connecting a local display

Enhanced Technical Features
● Supports video resolutions up to 1920 x 1080 (1080p) @ 60 Hz
● Uses H.264 video compression standard
● Transmits on 20–60 kHz IR frequency
● Extends IR control signals that control a source from a remote display
● Supports RS-232 serial baud rates up to 57600 Bps
● HDCP and 3D compatible

Plug and Play Functionality
● No software or drivers required
● Hardware included for mounting on wall, rack or pole

● Units connect point-to-point without a switch up to 100 m (328-ft.) apart
● Designed for managed network switches with IGMP
● Supports video resolutions up to 1920 x 1080 (1080p)
● Plug and play—no software or drivers required
● Mounts on wall, rack or pole with included hardware

Package Includes

● Transmitter unit
● Receiver unit
● (2) External power supplies w/NEMA 1-15P plug (Input: 100–240V, 50/60 Hz, 0.5A; Output: 5V, 2A)
● Plug adapters for U.S., U.K., Europe and Australia
● IR-In cable
● IR-Out cable
● 3.5 mm to DB9 adapter cable (M/F)
● 3.5 mm to DB9 adapter cable (M/M)
● Mounting hardware
● Owner’s manual

Tripp Lite DisplayPort Audio/Video with RS-232 Serial and IR Control over IP Extender Kit, 1920 x 1080 (1080p) @ 60 Hz, 200 m, 1920 x 1080 pixels, AV transmitter & receiver, 200 m, 3D, Black, HDCP

Tripp Lite DisplayPort Audio/Video with RS-232 Serial and IR Control over IP Extender Kit, 1920 x 1080 (1080p) @ 60 Hz, 200 m. Type: AV transmitter & receiver, Maximum resolution: 1920 x 1080 pixels, Cable types supported: Cat5, Cat6. AC input voltage: 100-240 V, AC input frequency: 50 - 60 Hz, Operating voltage: 5 V. Package width: 147.3 mm, Package depth: 287 mm, Package height: 78.7 mm. Cables included: Audio (3.5mm), IR. Master (outer) case width: 439.9 mm, Master (outer) case length: 322.1 mm, Master (outer) case height: 320 mm